We sew a robe with a smell on a simple pattern

Bathrobe with odor is considered the most comfortable home clothes. He does not hamper the movements, allows you to feel comfortable and cozy. In a bath or sauna, such clothes successfully replace the towel. Such a product can be bought in a store or sewed on its own using the patterns suggested in this article. A kimono robe can be made from various materials.

How to sew a robe with a smell?

If you decide to show your creativity and independently sew a homemade robe with a smell, use the following instruction.

• First of all, we determine the silhouette of the product. The easiest way is to sew a loose robe with vtachnymi cuffs and sleeves. The pattern of such a model can be easily found on the Internet or a thematic magazine for needlewomen.
• We take measurements and determine the length of the robe. As a rule, a kimono is made short, but you can extend it a little.
• We choose the material for making a smock dressing gown. If you decide to sew homemade summer clothes yourself, give preference to light silk, which is not so hot. You can also use cotton satin or cotton cloth - it all depends on your preferences.
• Based on the measurements taken, we build our own pattern and proceed to sewing.

Simple pattern of dressing gown with sleeves and smell for beginners

Using the presented drawing, it is possible to create your own pattern easily. Preliminarily remove all the measurements that you may need. All the details come with the allowance, except the pocket. To cut the pocket, add 4 cm and 1 cm from all other sides to the upper cut. Also do not forget about the belt. Adjust its length can be at your discretion - it all depends on the volume of your waist. According to this pattern, a beginner seamstress will be able to cut the fabric to create a robe with a smell and sleeves. The proposed figure is used for self-tailoring women's home dressing gown. However, for a similar example, you can create a pattern for a male or a child kimono.

The basic stages of making a dressing gown

• The prepared parts of the gear and backrests are connected together, the front side inward. Shoulder stitches are gently weed and swept. The width of this seam should be 1.5 cm.
• We cut out the chalice collar according to the pattern. In this case, the central seam of this part will be on the back. We grind it with shelves. To make the wrench look perfect, you can glue the under-collar with the collar of non-woven fleece and sweep the inner slice.
• In the center of the back we grind the gate into the neck. Gradually, we rub off the sides of the dressing gown with a one-piece collar. The width of the seam is about 0.7 cm.
• For finishing the product, you can use edging. It must first be attached to each part of the smelling smock, and only then start to grind the individual elements.
• Sleeves are sharpened in the armhole from the notch to the notch. At the very bottom of the detail, you can make neat cuffs. They are cut out the same way as the bottom of the sleeve. If you do not want to spend too much time on it, just bend the edges and sweep.
• The allowance on the bottom edge of the dressing gown and the inner edges must be slightly pressed and carefully stitched, observing each notch.
• Together with the sleeves, we weak the side parts of the product. We use the width of the seam -1.5 cm.
• The upper part of the pocket must be swept and then bent. As an original finish you can use lace or satin ribbons. A little priutuzhivaem allowances and impose a detail on the shelf.
• Lower the article with a seam of 1 cm.
• At the last stage we make a belt. It should be sewn with one short and long side. Then turn the product out, bend the edge and staple the ends.

The original home dressing gown is ready. After a little training, you can sew your own gowns for a child or a loved one. Such an unusual present is sure to please your relatives.