Summer men's gloves without fingers

Summer men's gloves without fingers - an indispensable accessory for fans of an active lifestyle. For example, durable and comfortable gloves, crocheted, it is very convenient to use for fishing or cycling. Suitable knitted mittens for light repair and garden works. Appreciate this accessory and men, keen on sports, in particular, using in their training weights and bars.

• Yarn: Yarn Art Maldive 100% mercerized cotton 50 g / 90 m; Yarn consumption: 150 g.
• Density of knitting in the horizontal: 3.1 loops per cm.
• Tools: hook: 2.5 - 3.5
• Additional materials: two flaps of soft leather 10x10 cm.
• The size of the glove: 17 cm.

Selection of materials for crocheted male crochet mitts

The most practical and comfortable solution for summer gloves will be a cotton thread. Among its main advantages: hygienic, natural, wear-resistant. In addition, the thickness of the cotton thread provides a high strength of the product, so the associated gloves fit even for fishing or outdoor activities. In addition, men's gloves made of such a thread will hold well and will not rub or crawl.

As for the skin, which is used as an additional material for strengthening the strength of summer men's gloves by crochet, then preference should be given to natural soft skin. Of course, you can use an artificial substitute, but then you need to be prepared for the fact that the product will quickly lose its presentable appearance and require repair.

Men's gloves without fingers crochet - step by step instruction

The main part of the mitt

1. First, we determine the widest place of the hand and calculate the required number of loops in the ratio of 2 loops to 1 cm. In our case, we collect 48 air loops for a brush with a circumference of 24 cm.

2. We begin to knit the main part of the male gloves with no crochet. We send 8 rows.

Important! Summer men's gloves need to knit is not very tight, because the product of cotton thread after washing can become rougher and will begin to cause discomfort when socked.

The upper part of the glove

Before knitting the upper part of the glove, the number of loops should be calculated, so that the holes for the fingers are the same. You can also divide the total number of loops into four equal parts and then the holes for the fingers will be the same size.

1. Gently spread the mitten on a solid working surface. It is important that the loops of the back of the glove and palm are parallel. Thus, it will be enough to read only one side of the glove.
2. The number of loops is multiplied by two and divided by four. The resulting number will show the desired number of loops for one finger. In our master class, the number of hinges for the holes is as follows: 14 for the index and average, 12 for the anonymous and the little finger.
3. After the calculations, proceed to the design of the slits for the fingers. To do this, we tie each finger with three rows of columns without a crochet.

Bottom of the glove

1. We turn the product over and mirror the bottom of the glove. To do this, we bind 8 rows with columns without a crochet.
2. Beginning with the 9-11 series, we reduce the number of loops - after every 10 loops we combine two columns into one.

   Attention! Be sure to leave a slot for a thumb size of 15 loops.

3. The remaining six rows are knitted with columns without a crochet.

4. At the end we knit a thumb glove. It consists of four rows of islands. b / n.

5. Our man's glove is ready. The length of the finished product is 17 cm. You can make the glove higher by increasing the number of rows.

Cooking for Men's Summer Gloves

A leather insert on a man's glove without fingers in the palm of the hand is necessary in order to make the knitted product more durable and practical.

1. We take a flap of soft natural leather with a size of 10 by 10 cm.
2. Sew a flap to the glove using a large needle and ordinary thread.
3. Stylish and practical summer men's gloves without fingers - ready!